收藏本站
DS1822-PAR
WRITE SCRATCHPAD [4Eh]
This command allows the master to write three bytes of data to the DS1822-PAR’s scratchpad. The first
data byte is written into the T H register (byte 2 of the scratchpad), the second byte is written into the T L
register (byte 3), and the third byte is written into the configuration register (byte 4). Data must be
transmitted least significant bit first. All three bytes MUST be written before the master issues a reset, or
the data may be corrupted.
READ SCRATCHPAD [BEh]
This command allows the master to read the contents of the scratchpad. The data transfer starts with the
least significant bit of byte 0 and continues through the scratchpad until the 9 th byte (byte 8–CRC) is read.
If only part of the scratchpad contents is required, the master may issue a reset to terminate reading at any
time.
COPY SCRATCHPAD [48h]
This command copies the contents of the scratchpad T H , T L and configuration registers (bytes 2, 3, and 4)
to EEPROM. If the device is being used in parasite power mode, within 10 μ s (max) after this command is
issued the master must enable a strong pullup on the 1-Wire bus for at least 10ms as described in the
PARASITE POWER section.
RECALL E 2 [B8h]
This command recalls the alarm trigger values (T H and T L ) and configuration data from EEPROM and
places the data in bytes 2, 3, and 4, respectively, in the scratchpad memory. The master device can issue
“read-time slots” (see the 1-WIRE BUS SYSTEM section) following the Recall E 2 command and the
DS1822-PAR will indicate the status of the recall by transmitting 0 while the recall is in progress and
1 when the recall is done. The recall operation happens automatically at power-up, so valid data is
available in the scratchpad as soon as power is applied to the device.
DS1822-PAR FUNCTION COMMAND SET Table 4
1-Wire Bus Activity
Command
Description
Protocol
After Command is Issued
Notes
TEMPERATURE CONVERSION COMMANDS
Convert T
Initiates temperature
44h None
1
conversion.
MEMORY COMMANDS
Read
Scratchpad
Write
Scratchpad
Reads the entire scratchpad
including the CRC byte.
Writes data into scratchpad
bytes 2, 3, and 4 (T H , T L , and
BEh DS1822-PAR transmits up
to 9 data bytes to master.
4Eh Master transmits three data
bytes to DS1822-PAR.
2
3
configuration registers).
Copy
Scratchpad
Copies T H , T L , and
configuration register data from
48h None
1
the scratchpad to EEPROM.
Recall E
2
Recalls T H , T L , and
configuration register data from
B8h DS1822-PAR transmits
recall status to master.
EEPROM to the scratchpad.
NOTES:
1. The master must enable a strong pullup on the 1-Wire bus during temperature conversions and copies
from the scratchpad to EEPROM. No other bus activity may take place during this time.
2. The master can interrupt the transmission of data at any time by issuing a reset.
3. All three bytes must be written before a reset is issued.
10 of 19
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DS1822Z/T&R IC THERMOMETER ECONO DIG 8-SOIC
DS1870E-010+T&R IC CNTRLR RF POWER AMP 16TSSOP
DS18S20-PAR+T&R IC THERM MICROLAN HI-PREC TO-92
DS60R+T&R IC SENSOR MICRO CENTIGRADE SOT23
DV164102 KIT DEV RFPICKIT KIT 1
DVK90109 KIT DEV FOR MLX90109
DVK90121 KIT DEV FOR MLX90121
DXP18CN7515TL COUPLER FILM 75 OHM 0603
相关代理商/技术参数
DS1822+T 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Econo 1-Wire Digital Thermometer
DS1822+T&R 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer
DS1822+T&R 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1822-PAR 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1822-PAR/T&R 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
DS1822-PAR_07 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Econo 1-Wire Parasite-Power Digital Thermometer
DS1822-PAR+T&R 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer
DS1822-PAR+T&R 功能描述:板上安装温度传感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor